How To Patch Thermostat Hole

Fish the wire to the new hole. You can twist the wires around a pencil or other object to prevent them from coiling into the wall.

Nest Thermostat Install

This will allow it to adhere.

How to patch thermostat hole. This video is part of the heating and cooling series of training videos made to accompany my. Use sharp scissors to cut a wall repair patch so that it is approximately 1 in (2.5 cm) taller and 1 in (2.5 cm) wider than the hole in the wall. Remove the paper backing from the patch making sure to cover your hole.

The attachment screws would have to be driven below the wall surface so you can patch the screw holes at the same time you fill the main hole with joint compound. Unscrew the thermostat mounting case from the wall. This isn't ideal, because it can cause high levels of kr in the back half of the ¼ mile.

Press firmly on the patch to ensure a good bond with your wall. It could be old thermostat or humidifier control, that is no longer connected and functiona. Alternatively, you could make your own stylist oversize backplate and install your new thermostat on it.

I discovered there is a big hole leading to the outside that the previous owner hid, but isn't sealed properly. I.e., removes the dead leg. Share improve this answer answered sep 26 '20 at 12:49

Get a piece of wood large enough to cover the hole, attach that to the wall, then attach the thermostat to the wood. Make a hole somewhere else. 1/2 thick should be plenty strong.

Now you are ready for your 3m™ patch plus primer. Sometimes you might end up with unwanted old control on the wall. I was thinking of getting gorilla glue, glue down the an anchor on the lower border of the hole and then put the screw in to hold it.

Quick, easy, cheap, and you won't have to deal with patching the drywall. Make sure the wire can get there. Be careful not to let the wires slip into your wall.

This one is about plugging the hole behind the wall thermostat. You will feel a slight tackiness to your patch which will help hold it to the wall while your patch plus primer dries. We've all experienced that 'doh!' moment when we've drilled a hole that ends up being too big.

It doesn't look like the original screws were screwed into anything substantial.the area where i'm trying to patch around the hole in the wall to provide a solid surface to rehang the thermostat screws, but after three coats, the patching is still flimsy and. Slowly remove the remaining parts of the thermostat and let the wires slide out the hole in the center. Home → uncategorized → how to patch thermostat hole.

You can eliminate this problem by drilling holes in the thermostat to allow a small amount of coolant to consistently flow. Without a picture with wiring shown it's tough to really say if you can patch in drywall easily, or insert a backer. Also, the bleed hole should be placed in the 12 o'clock position.

It's not that heavy so it might work. Since the edges will be visible, use solid wood, not plywood. Put a smaller wooden backplate to support the new drywall.

Their patch was just a piece of wood with nails, but it is so badly secured, it lets tons of air out and isn't allowing the furnace vents to build pressure. When you come back to your starting point, slightly overlap the tape and make another pass around the duct. Create a repair patch that is about 1 in (2.5 cm) bigger than the hole.

This will ensure you get the most air bleed from the system. Cut a new piece of drywall the size of the hole. This means the coolant around the cylinders and heads might reach 250 degrees before the stat even begins to open.

Sandy.we have removed and use wood filler, sanding then paint and it worked nicely, however, there really was no damage other than the small holes. You can also just buy a blank wall plate from the hardware store,drill a hole, or buy one with a hole already in it, and then mount your google nest thermostat to the white wall plate. Smooth and sand, then use plastic anchors to secure your new thermostat.

I have been trying to find advice on how to do something similar to patch a rock lath plaster wall around my thermostat wires. Continue this until the entire hole is covered. How to patch thermostat hole.

Putting in new thermostat Old thermostat, hole Geoff cut